Search results

I have a new set of CNC machined 4 bolt splayed main caps. The end 2 caps are 2 bolt mains and the center 3 are 4 bolt. They include a full set of ARP studs with nuts and washers. The center three use grade 8 bolts on the outside 2 bolts. I will get pics of them off the block. They were...

I have a hood scoop from an 03 Mach 1. Includes the rubber surround. $100 Shipped OBO. It's the last of my mustang junk and I want it out of the garage.

This is an OEM ford block. 1997 non roller. Bores are fresh .030" over. Main caps have been replaced with CNC 4 bolt splaied mains on the center 3 and CNC 2 bolt end caps. It just needs to be line bored to be finished. It was hot tanked and magnafluxed. ARP main studs have been installed...

Car runs and drives perfect. Long tube headers, off road X pipe and flowmaster super 44 cat back exhaust. Other wise all stock. 161,000 miles on the clock. Power everything and it all works. Car is solid with only 2 little spots of surface rust. Underside is super clean. Interior is clean...

Can someone please for the love of god locate a part number for the original 40 series flowmaster mufflers to fit a GT fox body. 2.5" inlet and outlet. I don't remember the fox having an offset inlet and outlet but those are the only ones I can find.

I like the car but I recently figure out that it doesn't have a transfer case or four wheel drive. Car is solid. Body is good but the paint is faded in spots. It runs and drives like a new car. Super tight going down the road and the AOD shifts perfect. Car has 161,000 miles on it. Since I...

Where do you buy the gears to correct the speedo after a rear gear change?

Looking for a set of 3.73's for an 8.8". FRPP only, thanks.

I like a 6 speed but at the same time I know that your never going to out drive an auto at the 1/4 mile. With that said, what does the stock auto hold for power and how much money has to be put into it to make it hold even more? I am sure a clutch will keep the 6 speed on par with HP but I am...

Where can I find the rules that tell you what equipment you need to run certain times in the 1/4 mile?

Looking for a decent set of tires to throw on the Pony rims. Car has made progress but it is being thrown on the back burner in an attempt to finish other projects. If I don't find any in the next week or so I will have to buy new ones but I really don't want to.

YouTube - Ford Mustang Launch (street)

A set of 4 Gorilla Silverbacks. Two of them are 30x9x14 and two of them are 30x11x14. These are for a 14" rim. About 400 miles on the set. Fronts look brand new and rears are just starting to round off the front edge of the center lugs. No patches, plugs or cuts. Rims are 14" Motorsport...

Ford : Mustang - eBay (item 320636845519 end time Jan-04-11 16:06:36 PST)

I am looking for some one to measuer the actual height of a nitto 555r in 275/40-17 and 245/45-17 mounted on a rim and inflated. I know they will be shorter than the current set up on the pony rims and I need to figure out the suspension so I don't have stupid looking fender gaps.

LiveLeak.com - Blow Turkey Call

I would like them to be black but I will consider anything other than chrome because I can always paint them. Only tires I would take with them woule be Nitto 555R's 275 rears and 245 fronts. I will be ready to buy them after I make sure I survive the holidays and new years. If I don't find...

We have a wii and it's fun but The more I look at some of the new games the more I realize I want more. We basicly use the wii when friends come over and do alot of drinking. Then we break out the balance board and see who falls over. The two trailers I just watched were for Gran Torino 5 and...

I think I need a 4 door.

I just got too see a set of American Racing Headers for the first time in person and all I could say was....WOW. By far the nicest looking and best constructed headers I have ever seen. Buddy of mine ordered a set for his 09 ZO6 on Friday, they were built to order on Monday and they were...